To Edit the Transmitter settings
Open T6Config
Select Setting and choose serial port
Make sure your Tx is communicating by moving the sticks and seeing the Green/Black bars moving.
Click Get User to retrieve the config from Transmitter
(you may want to save the current settings at this time to backup your previous settings)
Make Changes (note: once you make a change, it is saved to the transmitter)
Save to a file

To Recall saved changes and alter the Transmitter to the saved changes:
Open T6config
Select Setting and choose serial port
Make sure your Tx is communicating by moving the sticks and seeing the Green/Black bars moving.
Click Get User
Select Open and select file. Once you open the file, the config is instantly saved to the Transmitter.


Here are the default Blueray settings.

End Point
Ch 1 100 100
Ch 2 100 100
Ch 3 100 100
Ch 4 100 100 (suggest for beginner to set this to 60 to reduce Piro rate/tail spin rate in Heading hold mode)
Ch 5 120 120 (suggest setting this to 80 instead to limit gyro gain, you can turn this up later)
Ch 6 100 100

cyclic servos:
Ch 1 = rear left (bottom rear cyclic servo)
Ch 2 = front cyclic servo
Ch 6 = rear right (top rear cyclic servo)

Reverse
1 reverse
2 reverse
3 normal
4 reverse
5 reverse
6 normal

Subtrim (set these for each individual heli to set swash level at center stick in idle up)
Search for info on leveling a swash (with motor disconnected)
Ch 1 -70
Ch 2 30
Ch 3 0
Ch 4 60
Ch 5 50
Ch 6 10

DR   on  off
ch 1 100 100
ch 2 100 100
ch 4 100 100

Mode 
Model 2 (mode 2)

Type : Heli-120 (120 degree CCPM)

Throttle curve 
Normal
EP0 0%
EP1 25%
EP2 50%
EP3 75%
EP4 100%

Idle UP
EP0 100%
EP1 85%
EP2 80%
EP3 85%
EP4 100%

Pitch Curve 
Normal
EP0 40% (30)
EP1 45% (40)
EP2 50%
EP3 75%
EP4 100%

Idle Up
EP0 0%
EP1 25%
EP2 50%
EP3 75%
EP4 100%

Swash AFR
Ch 1 (Aileron) 50%
Ch 2 (Elevator) 50%
Ch 6 (Pitch) -80% (suggest -60%)

Mix1 [use VR(B) as gyro gain control]
Source VRB
Des Ch5
Up rate 100
Down rate 100
Switch On

Mix 2 (disableD)
Source VRB
Des Ch6
Up rate 100
Down Rate 100
Switch OFF

Mix 3 (disabled)
Source CH3
Des Ch 1
Up Rate 36%
Down Rate 0
Switch Off

Switch A 
Thro Cut

Switch B
Nor/ID (normal Down, idle up- UP)

VR(A) Pitch adjust CW = more pitch, CCW = less pitch. 
Adds/removes pitch across entire pitch curve.

VR(B) Null (used in Mix 1)



*initial setup procedure
Mark each blade with colored tape near tip.
Unplug motor
Power up heli and tx
Connect to PC
set idle up
Set collective pitch (left) stick to center vertical position.
Adjust sub trims of channels 1,2 and 6 to get swash level.
Check pitch, of both blades at the same point of rotation (facing forward). should be 0 degrees.
If both are not, use the blade that is closest to 0 degrees for checking pitch.
Get the closest blade to 0 pitch by adjusting the VR(A) knob. Note position.
Adjust the pitch of the opposite blade to be at 0 degrees.
Set pitch stick to full up.
Adjust swash AFR value for Ch 6 so that full pitch is +9 degrees. (-60?)
Verify pitch stick at full negative is about -9